Heckmann Building Products Inc.
1501 N. 31st Avenue - Melrose Park, IL 60160 USA
800-621-4140  Fax 708-865-2640

Download PDF Format

Wall Tie Specifications

SECTION 04085

MASONRY ANCHORS AND ACCESSORIES

PART 1 GENERAL

1.1 SECTION INCLUDES

*******************************************************
NOTE: Delete items below not required for project.
*******************************************************

A. Masonry veneer anchors and ties.

B. Stone veneer anchors and ties.

C. Masonry accessories.

1.2 RELATED SECTIONS

A. Section 04810 - Unit Masonry Assemblies.

B. Section 04851 - Cut Stone Veneer.

C. Section 04852 - Stone Masonry Veneer.

1.3 REFERENCES

*****************************************************************

NOTE: Delete references from the list below that are not actually required by the text of the edited section.

*****************************************************************

A. ASCE/ACI 530.1 Specifications for Masonry Structures; 1995.

B. ASTM A 153/A 153M - Standard Specification for Zinc Coating (Hot-Dip) on Iron and Steel Hardware; 1998.

C. ASTM A 167 - Standard Specification for Stainless and Heat-Resisting Chromium-Nickel Steel Plate, Sheet, and Strip; 1996.

D. ASTM A 240/A 240M - Standard Specification for Heat-Resisting Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels; 1998b.

E. ASTM A 276 - Standard Specification for Stainless Steel Bars and Shapes; 1998b.

F. ASTM A 479/A 479M - Standard Specification for Stainless and Heat-Resisting Steel Bars and Shapes for Use in Boilers and Other Pressure Vessels; 1997a.

G. ASTM A 580/A 580M - Standard Specification for Stainless Steel Wire; 1998.

H. ASTM A 653/A 653M - Standard Specification for Steel Sheet, Zinc-Coated (Galvanized) or Zinc-Iron Alloy-Coated (Galvannealed) by the Hot-Dip Process; 1998.

I. ASTM B 633  Standard Specification for Electrodepositied Coatings of Zinc on Iron and Steel; (Reapproved 1994).

1.4 SUBMITTALS

A. Submit under provisions of Section 01300.

B. Product Data: Manufacturer's data on each type of product furnished.

PART 2 PRODUCTS

2.1 MANUFACTURERS

A. Acceptable Manufacturer:
Heckmann Building Products Inc.,
1501 N. 31st Avenue
Melrose Park, IL 60160.
Tel: (708) 865-2403 Fax: 708-865-2640
Email: info@heckmannanchors.com.
Website: www.heckmannanchors.com.

***********************************************
NOTE: Delete paragraph below; coordinate with Division 1 requirements.
***********************************************

B. Requests for substitutions will be considered in accordance with provisions of Section 01600.

C. Substitutions: Not permitted.

2.2 APPLICATIONS

A. Provide anchoring systems that comply with ACI 530.1/ASCE 6/TMS 602.

************************************************
NOTE:Delete the following items not needed for your project
************************************************

B. Products.
1. NO. 251 Z-WIRE WALL TIE
[3/16 inch (4.76 mm)][1/4 inch (6.35 mm)] diameter x [length] x 2 inch (51 mm) bends.

2. NO. 253 RECTANGULAR WIRE WALL TIE
[3/16 inch (4.76 mm)][1/4 inch (6.35 mm)] diameter x [length] x [width].

3. NO. 260 CORRUGATED WALL TIE
[gage] x [width] x [length]

4. NO. 268 METAL LATH WALL TIE
[3.4 lb galvanized lath][2.5 painted lath] x [length] x width]

5. NO. 269 WIRE MESH WALL TIE
2 x 2 (1/2 inch (12 mm)) 16 gage hotdip galvanized wire x [length] x [width]

6. 186 BRICK VENEER ANCHOR (NO HOLE)
[gage] x [width] x [length] x [bend length]

7. 187 HOLE-TYPE BRICK VENEER ANCHOR
[gage] x [width] x [length] x [bend length]

8. 188 SLOTTED TYPE BRICK VENEER ANCHOR
[gage] x [width] x [length] x [bend length]

2.3 MATERIALS

A. Steel Types

1. Stainless Steel: Type 304.

A. Sheet Metal: ASTM A 167 or ASTM A 240/A 240M.

B. Wire: ASTM A 580/A 580M.

C. Bars: ASTM A 479/A 479M, annealed and ground.

D. Plates, Bars, and Shapes: ASTM A 167 or ASTM A 276.

2. Hot-Dip Galvanized Steel: Hot-dip galvanized after fabrication in accordance with ASTM A 153/A 153M, Class B-2.

3. Mill Galvanized Steel:

A. Sheet Metal: ASTM A 653/A 653M, G60 coating.

B. Wire: ASTM A 641, regular coating; minimum 3/16 inch (4.76 mm) diameter.

PART 3 EXECUTION

3.1 INSTALLATION

A. Install as specified in applicable masonry section(s) and in accordance with manufacturer's instructions.

END OF SECTION

 

Home  •   Products  •  Specifications  •  Submittals  •   CAD Details  •   Test Data  •   PDF Files
Catalog # Index  •   M.S.D.S.  •   Credit App.  •   Links  •   Trades Shows  •   Contact  •   History

 

© Copyright 1999 Heckmann Building Products Inc.