7"
(178 mm) long x 2" (51 mm) wide x 1/8" (3.17
mm) thick x 1-1/2" (38 mm) bend. Standard flange
slot is 5/8" (16 mm) wide x 1" (25.4 mm)
deep x 1" (25.4 mm) from end. Order in pairs
with one left and one right anchor. Specify steel
type.
7"
(178 mm) long x 2" (51 mm) wide x 1/8" (3.17
mm) thick x 1-1/2" (38 mm) foldback. Standard
flange slot is 5/8" (16 mm) wide x 1" (25.4
mm) deep x 1" (25.4 mm) from end. Corrugated
wall tie is 22 gage x 1" (25.4 mm) wide x 24"
(610 mm) long. Order in sets of left & right anchors
and a No. 190 Corrugated wall tie. Specify steel type.
6"
(152 mm) long x 1" (25,4 mm) wide x 1/4"
(6.35 mm) thick x 2" (51 mm) bend on flange and
1-1/4" (32 mm) bend into masonry, electro-galvanized
after fabrication. Weld to structural steel. Order
in pairs. Specify steel type.
7"
(178 mm) long x 2" (52 mm) wide x 1/8" (3.17
mm) thick with 4-1/2" (114 mm) of corrugation.
Order by piece, anchors are reversible for left or
right hand use. Specify steel type.
3"
(76 mm), 5" (127 mm), 7" (178 mm), and 9"
(229 mm) lengths from inside of flange slot to masonry
bend x 3/16" (4.76 mm) or 1/4" (6.35 mm)
diameter wire. Standard flange slot is 1/2" (12.7
mm) x 2-1/2" (63.5 mm). Bend is 2" (51 mm).
Order by piece. Specify steel type.
No.
191 Top Flange
No. 192 Bottom Flange Column Anchor:
10”
(254 mm), 12” (304.8 mm), and 14” (355.6
mm) long from inside of flange hook to bend x 1-1/4”
(32 mm) wide x 1/8”
(3.17 mm) thick + 1-1/2” (38 mm) bend.
Length
required x 1-1/4" (32 mm) wide x 1/8" (3.17
mm) thick x 1-1/2" (38 mm) foldback. Specify
length from hook to start of twist. Corrugated wall
tie is 22 gage x 1" (25.4 mm) wide x 24"
(610 mm) long. Order in sets of left & right anchors
and a wall tie. Specify steel type.
+
Specify
length required 1-1/4" (32 mm) wide x 1/8"
(3.17 mm) thick. Order in Pieces, anchors are reversible.
Specify Stainless, Hotdip Galvanized After Fabrication,
or Mill Galvanized.
Specify
overall Length and Length from hook to start of twist.
Specify diameter and location of hole for bolting
the anchor to the beam. 1-1/4" (32 mm) x 1/8"
(3.17 mm) thick. Order by pieces, anchors are reversible.
Specify steel type.
10"
(254 mm), 12" (305 mm), 14" (356 mm), and
16" (406 mm) long from inside of flange slot
to masonry bend x 3/16" (4.76 mm) or 1/4"
(6.35 mm) diameter wire. Standard flange slot is 1/2"
(12.7 mm) x 2-1/2" (63.5 mm). Order by pieces.
Specify steel type.
