Channel Slot Anchors
                 

Click HERE for
Channel Slot Systems


CHANNEL SLOT ANCHORS
Click HERE for Channel Slot Specifications
 

No. 122 Channel-Slot Partition Anchor:

12" (305 mm) x 1-1/4" (32 mm) wide x 16 gage.

Download 3-D Cad File

Specification MSWord
Specification PDF

No. 123 Channel-Slot Horizontal Triangular Anchor:

1/8" (3.17 mm) thick anchor furnished loose with No. 316 Triangle Ties. Use with Slots installed Horizontally. Channel Slot projects 1/2" (12.7 mm)

Download 3-D Cad File

Product Submittal Sheet - html
Product Submittal Sheet - PDF

Specification MSWord
Specification PDF

No. 125 Channel-Slot Furring Anchor:

1-1/2" (38.1 mm) long x 16 gage. Use with thin masonry or tile veneers.

Download 3-D Cad File

Specification MSWord
Specification PDF

No. 129 Channel-Slot Triangular Ties:

12 gage anchor factory assembled to No. 316 Triangular Tie. Specify length of tie and type of steel. Channel slot anchor projects 1/2" (12.7 mm).

Download 3-D Cad File

Product Submittal Sheet and test data - html
Product Submittal Sheet and test data - PDF

Specification MSWord
Specification PDF

No. 134 Channel Slot Corrugated Anchor:

3-1/2" (89 mm), 5-1/2" (140 mm), and 7-1/2" (190 mm) long x 1-1/4" (32 mm) wide in 12 gage and 16 gage as standards. [Not available in 3/16" (4.7 mm) stainless steel.]

Download 3-D Cad File

Product Submittal Sheet - html
Product Submittal Sheet - PDF

Test Data pullout from bricks

Specification MSWord
Specification PDF

No. 135 Channel-Slot Bent Anchor:

Length and Bend made to order. Use "inside" dimensions to specify length and bends. For stone and masonry block.

Download 3-D Cad File

Product Submittal Sheet - html
Product Submittal Sheet - PDF

Specification MSWord
Specification PDF

No. 136 Channel-Slot Split-Bend Anchor:

Length and split bend made to order. Use "inside" dimensions to specify length and bends. Use to anchor upper and lower stones.

Product Submittal Sheet - PDF

Download 3-D Cad File

Specification MSWord
Specification PDF

No. 137 Channel-Slot Pin Anchor:

Made to Order. No. 155 Dowel Pin furnished loose or welded in place. Specify length to center of hole and size of pin. Hole is 1/16" (1.59 mm) greater than diameter of pin.

Download 3-D Cad File

Product Submittal Sheet - html
Product Submittal Sheet - PDF

Specification MSWord
Specification PDF

No. 138 Channel-Slot Flat Anchor:

Made to Order for field bending, drilling, or welding on the job.

Download 3-D Cad File

Product Submittal Sheet - html
Product Submittal Sheet - PDF

Specification MSWord
Specification PDF

No. 362 Channel-Slot Seismic Anchor:

Made to Order. Tab holds masonry reinforcement or pencil rod.

Product Submittal Sheet - html
Product Submittal Sheet - PDF

No. 138-R Threaded-Rod Anchor:

Made to Order. Rod welded 1" (25 mm) to flat anchor. Specify diameter and lengths of flat anchor and threaded rod. Specify nut and washer if required.

Specification MSWord
Specification PDF

 

No. 397 T-Type Groutless Channel Slot Anchor:

11gage thick x 3-1/4” wide with the Twist-On™ Channel Anchor on one end and with a 1-1/ 2" x 16" long Corrugated Anchor Bar factory-welded onto the other end.

Product Submittal Sheet - PDF

 
     
 
Heckmann Home Page   Back To Top