 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Heckmann
Ceiling Hangers are the convenient and reliable
way to suspend ceilings and lightweight fixtures
from concrete slabs.
Other methods require difficult
and dirty overhead drilling, or rely on powder-actuated
fasteners which can damage concrete. Hangers
are typically spaced 2 ft. (610 mm) o.c. to
allow for flexible layout of ceilings.
Use
#444 Threaded Inserts to support heavier loads. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
#460: Nailer Ceiling Inserts
Install
by driving points of insert into wood
forms. When forms are stripped, the 5/16"
(7.9 mm) diameter hole projects below
concrete slab. Fabricated of 14 gage mill
galvanized steel with overall dimensions
1" (25.4 mm) wide x 2-3/16"
(55.5 mm) high. Average pullout 1,259
lbs.
Download
2-D Cad File Test
Data |
|
|
|
|
|
| |
|
|
|
| |
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
#461: Ceiling Hanger Insert
Economical
to use, simply nail or tape inserts
to forms for either precast or cast-in-place
concrete. Shells allow ceiling suspension
wires to be looped over wire clips
embedded in concrete. Shell is 26
gage galvanized steel. Wire clip
is 3/16" (4.76 mm) dia. galvanized
wire. Use with 1/4" (6.35 mm)
dia. maximum hanger wires or pencil
rods. Average pullout 1,905 lbs.
Download
2-D Cad File Test
Data |
|
|
|
|
| |
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
V-Type
inserts can be set in joints of precast slabs
which have keyways between slabs. T-Type inserts
can be set in joints of precast slabs with square
edges. For consistent installation, use tape to
hold inserts in place until adjacent slabs are
placed.
Standard inserts are 14 gage mill galvanized
steel. Also available in custom sizes. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
#486: V-Type
9"
(229 mm) long x 1" (25.4 mm)
wide with two 3/8" (9.5 mm)
diameter holes. "V" is
5/8" (16 mm) long x 1/4"
(6.35 mm) deep centered 5/8"
(16 mm) from top. Download
2-D Cad File
Download
3-D Cad File |
|
|
#487: Double V-Type
9-1/2"
(241 mm) long x 1" (25.4 mm)
wide with two 3/8" (9.5 mm)
diameter holes. "V's"
are spaced 1-3/8" (35 mm) o.c.
starting 5/8" (16 mm) from
top. Download
2-D Cad File
Download
3-D Cad File |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
#488: T-Type
6"
(152 mm) long x 1" (25.4 mm)
wide with one 3/8" (9.5 mm)
diameter hole. Horizontal flanges
are each 2" (51 mm) long. Download
2-D Cad File
Download
3-D Cad File |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
